Home > ELECTRICAL > ROUGH ELECTRICAL > ELECTRICAL BOXES
We found 227 results matching your criteria.
Choose a sub category:
OUTLET BOXES PVC SWITCH BOXES UTILITY BOXES
OCTAGON BOXES CEILING BOXES BOX COVERS
ELEC BOX SUPPORTS SPECIALTY BOXES
Sort By:
1 2 3 4
Thomas & Betts B118A Switch Box Thomas & Betts B120A-UPC Switch Box Thomas & Betts B122A-UPC Wall Box
With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.
Hubbell 860 Raised Blank Utility Box Cover Hubbell 864 Utility Box Cover Hubbell 865 Utility Box Cover
Steel box cover, blank with no knockouts. 2-5/16" wide x 4-3/16" tall. UL Listed. Steel box cover for duplex receptacle. Rugged construction. 2-5/16" wide x 4-3/16" tall. UL Listed. Steel box cover with single toggle switch opening in the center. 2-5/16" wide x 4-3/16" tall. UL Listed.
Hubbell 8752 Square Flat Blank Electrical Box Cover Carlon HB1BL Blank Handy Box Cover Carlon HB1GF Handy Outlet Box Cover
Rugged construction, used to close an outlet box. 4" square. Angled mounting slots allow for correction of box misalignment. UPC bar code. UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 1/2" knockout. 4.3" length x 2.38" width. UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 4.3" x 2.38". UL Listed.
Carlon HB1SW Handy Box Cover Carlon HB1DP Handy Box Cover Hubbell 722 Octagon Flat Blank Electrical Box Cover
Made of a durable polycarbonate material that is virtually indestructible. 4.3 length x 2.38 width. UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 4.3" length x 2.38" width. UL Listed. Rugged construction, used to close an outlet box. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed.
Thomas & Betts BH122A-UPC Outlet Box Hubbell 863 Utility Box Cover Raco 8977 Electrical Box Supports
Lightweight design and durable plastic. Listed for masonry walls. Safe to install and will never rust or corrode. Includes nails for quick, easy installation. 22 cubic inch rigid wall. 3-7/8" x 2-3/8" x 3-3/4". UL Listed. Steel box cover with single 1.406" receptacle opening in the center. Rugged construction. 2-5/16" wide x 4-3/16" tall. UL Listed. Use two to mount switch box with plaster ears to hollow wall. Slips between box and wall, tabs bend inside box.
Carlon B112HB Handy Box Hubbell 861 Utility Box Cover Hubbell 8660 Utility Box
PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. Includes hardware for quick, easy installation. Steel box cover with 1/2" knockout in the center. 2-5/16" wide x 4-3/16" tall. UL Listed. Used for convenience outlets, switch boxes or small junction boxes. Drawn construction and raised grounding provision. Acceptable for use in 2-hour rated walls. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Two 1/2" knockouts (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed.
Hubbell 8753 Square Flat Electrical Box Cover Hubbell 724 Octagon Flat Electrical Box Cover Thomas & Betts B114R-UPC Switch Box
Steel box cover with single 1/2" knockout in the center. 4" square. Angled mounting slots allow for correction of box misalignment. UL Listed. Steel box cover with single 1/2" knockout in the center. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. Old work wall case. Safe, non-conductive. Two Zip-Mount retainers. Four integral clamps, two each end; mounting ears. 14 cubic inch,  2-3/4" x 2-1/4" x 4-1/8". UL Listed.
Thomas & Betts B232A-UPC Outlet Box Hubbell 703 Round Flat Ceiling Pan Cover Thomas & Betts B520A-UPC Ceiling Box
New work safe, non-conductive. With captive nails. Eight integral clamps, four each side. 32 cubic inches. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. 3" depth x 4" x 3-3/4". Steel box cover with 1/2" knockout in the center. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. With captive nails. 3/0 - 4/0 combination. Fixture spacing for 2-3/4" - 3", 6 integral clamps. 4" diameter non-metallic ceiling box, 20 cubic inch volume. Listed for fixture support up to 50 lb. 4" diameter x 2-1/4" depth. Meets NEMA OS-2, UL Listed. RoHS Compliance.
Hubbell 8772 Square Raised Device Box Cover Carlon E460R-CAR Blank Round Outlet Box Cover Hubbell 8192 Outlet Box
Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed. High impact lightweight round blank PVC cover for 4" round boxes to make junctions. UL Listed. Conduit wiring system. Installed in ceilings or walls for lighting fixtures, switches or receptacles. Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for surface mount applications in ceilings or walls for lighting fixtures or receptacles. Eight 1/2"and four 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). 4" square x 1-1/2" deep - 21.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. UPC bar code.
Carlon A410R-CAR Square Electrical Box Cover Carlon A400R-CAR Square Blank Electrical Box Cover Raco 8768 Mud-Ring Raised Square Electrical Box Cover
Suitable for tile, plaster, sheetrock, paneling, masonry and all wall coverings. Brilliant electric blue. UL Listed. Two gang blank rise. Carlon blue color. Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed.
Carlon A420RR Raised Tubing Electrical Box Cover Thomas & Betts B108B-UPC Outlet Box Carlon B118B-UPC Switch Box
Suitable for paneling masonry, plaster, sheetrock, tile and all wall coverings. Brilliant electric blue. UL Listed. New work applications, shallow PVC switch box. Integral brackets. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed. Safe, non-conductive. With bracket for 3/8" to 5/8" wallboard. Steel and wood studs, 4 knockouts. 2-15/16" depth x 3-3/4" x 2-1/4".
Thomas & Betts B108R-UPC Outlet Box Hubbell 127 Octagon Box Raco 787 Mud-Ring Flat Square Electrical Box Cover
Designed and listed for use with non-metallic sheathed cable. With mounting ears. Permissible for use with 90 degree C connectors. 8 cubic inch capacity. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed. Two 1/2" and two 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). No bracket. Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code. Steel box cover, used to mount switch or receptacle. UL Listed.
Allied Moulded 1098-N Switch Box BOX OCTAGON 4IN 1-1/2IN DEEP  Carlon B1EXT-CRD Electrical Box
Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed. Four 1/2" conduit knockouts (sides). Four 1/2" conduit knockouts (bottom). No bracket. Used in the installation of ceiling or wall lighting fixtures or as a junction box. 1-1/2" deep, 15.5 cubic inch capacity. Not designed for ceiling fan support. 50 pound maximum recommended static load. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code. Extends an existing box by 1-1/8". Used to correct problems from remodeling where the wall surface is extended. Fits between the wiring device and the wall surface. Extends the switch or outlet box to flush with the wall. Works with all standard wiring devices. 2-1/4" x 3-1/4". UL Listed.
Raco 8756 Raised Square Open Electrical Box Cover Raco 8190 Outlet Box Carlon A471RR Round Tubing Ceiling Box Extender with Round Cover
Raised device cover. Used to hang light fixture from 4" square box. Not designed for ceiling fan support. Angled mounting slots allow for correction of box misalignment. Raised 5/8" - ears 2-3/4" - 4 cubic inches. UL Listed. UPC bar coded. Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for exposed work or surface mount applications. Combination cover screw heads provide for faster mudring/cover installation. Twelve 1/2" conduit knockouts (sides). Four 1/2" conduit knockouts (bottom). No bracket. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code. Half inch raised round high impact lightweight PVC. Used with nonmetallic sheathed cable in octagon boxes. Supports 50 pounds. UL Listed.
Raco 871 Wall Plate Raco 8189 Ceiling Outlet Box Allied Moulded P241 Switch Box
Two device switch box cover. Made from unpainted, pregalvanized steel. Used with  2 toggle 2 gang switch boxes. UL 514-A Listed, File E195978 / CSA Listed, File LR-1082. Welded square steel box, no bracket, installed in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices.  TKO 1/2" and 3/4" eccentric knockouts (Per U.L. 514-A, suitable for use without a bonding jumper in circuits above or below 250 volts).  Eight 1/2" and 4, TKO side knockouts, two 1/2" and 2 TKO bottom knockouts. Combination cover screw heads provide for faster mud ring/cover installation. UL 514-A Listed, File E195978. 21.0 cubic inch capacity. Acceptable for use in 2-hour rated walls. Residential thermoplastic switch or receptacle box. With angled nails. 3-9/16" depth x 2-1/4" width x 3-3/4" height. 24 cubic inch volume. Fire rating classification of 2 hours in wall and ceiling. UL Listed.
Thomas & Betts SC100RR Low Voltage Box Hubbell 731 Octagon Flat Electrical Box Cover Raco 7887RAC Old Work Cable Box
For telecommunications and other low voltage wiring. Suitable for old work applications. 1.18" depth x 2.18" x 3.05". Steel box cover for one duplex receptacle. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. Plaster ears, old work swing style clips secure box in wall. Integral clamps. Two hour fire rated. Mounting clips. 3" depth. 14.0 cubic inch capacity. UL Listed.
Raco 832 Blank Flat Square Electrical Box Cover Raco 791 Mud-Ring Flat Square Electrical Box Cover Hubbell 8778 Square Raised Device Box Cover
Rugged construction, used to close an outlet box. Key hole mounting feature allows for installation of cover without removing box screws. 4-11/16" square. UL Listed. Steel box cover, 4", used to mount two switches or receptacles. UL Listed. Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed.
MUD RING 4SQ SINGLE RAISED 3/4 Hubbell 8650 Welded Utility Box Raco 8769 Mud-Ring Raised Square Electrical Box Cover
Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed. Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed. Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed.
Carlon Flex-Plus A58381D-CAR ENT Flexible Raceway Switch Box Carlon B518A-UPC Ceiling Box Raco 8196 Electrical Box
Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed. With captive nails. 18 cubic inch volume. Listed for fixture support up to 50 lb. 3" diameter x 2-3/4" depth. Meets NEMA OS-2, UL Listed. Six 1/2" and 3 TKO conduit knockouts (sides). Three 1/2" and 2 TKO conduit knockouts (bottom). Combination cover screw heads provide for faster mudring/cover installation. FM bracket mounts flat on side of stud and provides a rigid, secure box installation. Square boxes are installed in ceiling or walls for lighting fixture or receptacles. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed.
Carlon Flex-Plus A58381E-CAR ENT Flexible Raceway Switch Box Carlon A615DE-CAR Flexible Raceway Ceiling Box Raco 8197 Welded Electrical Box
Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed. Safe, non-conductive. Quick connect. 20.5 cubic inch capacity. Knockouts 1/2" x 3/4". 4" diameter x 2-1/8" depth. Square 4" steel box for lighting fixtures, switches or receptacles where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 1-1/2" deep. 21.0 cubic inch capacity. Welded, with six 1/2" and three TKO  side knockouts, three 1/2" and two TKO  bottom knockouts. Flush FH bracket type for side mount of stud and features hooks that drive into face of wood stud for hands-free installation. UL Listed.
   
 
1 2 3 4